hifi engine

Manual Library / Kenwood

Kenwood KR-10000

AM/FM Stereo Receiver (1975-76)

add a review add a review

Kenwood KR-10000

Specifications

  • Tuning range: FM, MW

    Power output: 60 watts per channel into 8Ω (stereo)

    Frequency response: 10Hz to 40kHz

    Total harmonic distortion: 0.3%

    Damping factor: 50

    Input sensitivity: 2.5mV (mic), 2.5mV (MM), 150mV (DIN), 150mV (line)

    Signal to noise ratio: 70dB (mic), 77dB (MM), 95dB (DIN), 95dB (line)

    Output: 150mV (line), 30mV (DIN), 1V (Pre out)

    Speaker load impedance: 4Ω to 16Ω

    Dimensions: 574 x 198 x 350mm

    Weight: 16kg

    Year: 1975

  • Tuning range: FM, MW

    Power output: 80 watts per channel into 8Ω (stereo)

    Frequency response: 20Hz to 40kHz

    Total harmonic distortion: 0.3%

    Damping factor: 50

    Input sensitivity: 2.5mV (mic), 2.5mV (MM), 150mV (DIN), 150mV (line)

    Signal to noise ratio: 70dB (mic), 77dB (MM), 95dB (DIN), 95dB (line)

    Output: 150mV (line), 30mV (DIN), 1V (Pre out)

    Speaker load impedance: 4Ω to 16Ω

    Dimensions: 574 x 198 x 375mm

    Weight: 17.7kg

  • Tuning range: FM, MW

    Power output: 120 watts per channel into 8Ω (stereo)

    Frequency response: 20Hz to 40kHz

    Total harmonic distortion: 0.1%

    Damping factor: 60

    Input sensitivity: 2.5mV (mic), 2.5mV (MM), 150mV (DIN), 150mV (line)

    Signal to noise ratio: 75dB (mic), 80dB (MM), 100dB (DIN), 100dB (line)

    Output: 150mV (line), 30mV (DIN), 1V (Pre out)

    Speaker load impedance: 4Ω to 16Ω

    Dimensions: 574 x 198 x 375mm

    Weight: 18kg

    Year: 1977

Downloads

Comments

re: KR-10000

got an KR10000-II since 1979-80?
It allways did well but now takes about 15 to 30 minutes before its starts working (playing music). anybody who`s got an idea how to fix?
thanks, harald from Germany

re: KR-10000

recieved a kennie iii from my dad from 70s said it was not working. upon opening unit which wieghs a ton. witnessed some sort of burned area on power board, resistor swollen and even a cracked cement resistor, pretty bad condition. board is mor than likely not fixable. any ideas where a replacement can be found.

re: KR-10000

Did you ever find parts for the Kenwood KR 10000? I've found some online sites that have various used vintage audio gear pieces/parts listed by other users, however cannot recall exact URLs or names at the moment. If you are still seeking parts, I can find the sites again. I recently bought one of these KR 10000II receivers, and they have some great features & are worth repairing. Richard N.

This website is not affiliated with or sponsored by Kenwood. To purchase KR-10000/KR-10000 mkII/KR-10000 mkII spares or accessories, please contact the company via their website or visit an authorised retailer.