hifi engine

Manual Library / Technics

Technics SU-800

Stereo Integrated Amplifier (1988-90)

add a review add a review

Technics SU-800

Specifications

Power output: 50 watts per channel into 8Ω (stereo)

Frequency response: 20Hz to 20kHz

Total harmonic distortion: 0.04%

Damping factor: 50

Input sensitivity: 2.5mV (MM), 150mV (line)

Signal to noise ratio: 71dB (MM), 90dB (line)

Channel separation: 45dB (line)

Output: 150mV (line)

Speaker load impedance: 4Ω to 16Ω

Dimensions: 430 x 97x 240mm

Weight: 5.8kg

Downloads

Related Catalogues

For Music Lovers

HiFi

If you have any problems opening files please read the download FAQ. All files are provided under strict licence and reproduction without prior permission or for financial gain is strictly prohibited.

If you have additional documentation please consider donating a copy to our free archive.

Comments

re: SU-800

TECHNICS Class A amplifier, SU-800 2018.
Spec’ Check. [30 yrs on from manufacture]
Test Kit:
7.7Ω + 7.7Ω 100 + 100-Watt dummy load. [ audiosystems]
Microvoltmeter TM3B. * 1Hz to 3MHz range [Levell Instruments]
Dual beam scope 465. [Tektronix] (fed from TM3B output)
Signal source: Desk output. [Sound check CD2 Alan Parsons / Adobe Audition CS6 / Edit suite 1]
PM 5132 Function generator (set to sine) [Philips]
Only Main output considered. Loudness OFF.
Input = Aux. [ & tuner / tape] (Virtually no switch or control noise.)
L & R driven simultaneously – measured below clipping – at psu limiting. Very clean sine shape: careful study on scope.
Power output L = 46.8 watts [full Volume @1KHz sensitivity =140mV]
R = 51.9 watts [i.e. chnl match within ½ dB]
Volume set to full / no input. [reference 20V rms into 7.7Ω]
Signal to noise ratio L = - 90 dB [HF content - C = weighted -92 dB]
R = - 88 dB [HF content - C = weighted -90 dB]
Power band with at - 3dB ±1dB 10Hz – 40KHz stepped: Also, on sweep 20Hz 20KHz. [*after getting the correct range* !!]
Phono input sensitivity = 2.5mV @ 1khz for full output. [50Ω source]
Signal to noise ratio = - 62 dB L & R – 62 dB [input open circuit]
Signal to noise ratio = - 66 dB L - 64 dB & R – 68 dB [input 50Ω] Signal to noise ratio = - 64 dB L & R [I/P Shure M75 not optimised for 50Hz hum but seen on ‘scope] very useable!

re: SU-800

I own this amp + matching CD player (SL-P230) but i'm looking for the matching tuner... I have found an ST-Z250L online but not quite sure if it's the correct "look" to match these two beautiful devices. Any help?

re: SU-800

st-z450l

re: SU-800

I may have blown a fuse... on the left input... I can still hear the sound when I turn on the sound to near max... any way to reset this device? or change fuse?

karodimitrov's picture

re: SU-800

There are no fuses on the inputs.And there are too many options.Try to swap RCA cables.Red and white-change positions(white with red,and red with white).If now you hear left,and right is gone...it's good. Replace RCA cable.If not...This is step "A".Try it-it's easy.Step "B"-later.
Wanna know what's happen.:)))

This website is not affiliated with or sponsored by Technics. To purchase SU-800 spares or accessories, please contact the company via their website or visit an authorised retailer.